Blacksmith bending jig forge anvil blacksmithing tool (Watch the video demo) For Sale

This is a brand new indexable bending jig for bending iron or any other material you are forging. Bend hooks, eyes or any other forge work you want with consistency.

Comes with 8 dies made of 3/4\" thick 1045 steel, in 1\", 1-1/2\", 2\", 2-1/2\", 3\", 4\", 5\", and 6\" diameters. Each die has a series of holes spaced from it, in the base plate, to accept all common sized stock. Just pick the diameter bend you want, put the 1/2\"hardened dowel pin in the center hole of the base plateto accept the die and put the other 1/2\"dowel pin in the hole that best fits the stock you want to bend. Then just heat up your piece and bend it around the die. You can mark the base with soap stone if you wish for a reference stop to make repeated bends all the same.

With this set includes the 9\" diameter,3/4\" thickbase indexing plate, the 8 dies, three hardened dowel pins and a piece of square stock welded onto the bottom of the base indexing plate to acceptyour size hardy hole in your anvil.

********** PLEASE LET ME KNOW AT CHECKOUTWHAT SIZE SQUARE STOCK YOU NEED TO FIT YOUR HARDY HOLESO I CAN GET IT IN THE MAIL TO YOU AS SOON AS POSSIBLE **********

This jig also works well in the post vise and the square stock allows you to rotate the jigby quarter turnstoput it in the best position for the bend you are going to do. I probably use mine in the post vise more than the anvil, but it gives you the option to use either one.

I have soldmanyof these and everyone that I\'ve talked to says they wouldn\'t be without one! One guy even said you couldn\'t pry it from his cold, dead hands!!

Watcha video demonstration, just click on the link..http://youtu.be/U1mtCs9VnHU

******WARNING******** Watch out for imitations

There have been some look alike jigs being saleed off on I\'ve worked hard to develope a reputationfor selling a high quality tool. And from a distance they may look the same but they are not. The die sizes are the only thing thing that\'s the same. The hole spacing is not the same! My holes, although in the similar spiral pattern, are spaced in a manner that every hole is a specific distance away from any die that is used. any size die you put on has a hole to accept a pin to be spaced 1/8\", 3/16\", 3/8\", 1/2\", 5/8\", 3/4\", 7/8\", 1\", 1-1/8 and up in at least 1/8\" increments. 5\" die will only go to 1\" and the 6\" die will only go to 1/2\" because you run out of room on the base plate. each size mentioned has a 1/16\" extra clearance to accept that size stock so you have a little wiggle room so the stock doesn\'t stick. If you bend any stock bigger than 1/2\" you have to get the material good and hot as to not put too much stress on the dowel pins.

\"I have been searching for a good bending jig for 25 years. I counted 4 different jigs that I have bought over the years,

and I even have one that I made myself. After using your jig today, I know I will never use the others again.

Thank you so very much for making this elegant set available.\"

-doc23

SHIPPING SIDE NOTE: Shipping to Canada isno problem, the cheapest rate the US Post Office offers is $100.00 US Funds for two medium flat rate boxes (two boxes are needed because of weight restrictions).

For Mexico, Ireland and England shipping will cost $152 all other international shipping will be $172

You can see a demonstration of this jig being used at:http://youtu.be/U1mtCs9VnHU

FREE! Sellers: Add a FREE map to your listings. FREE!